Salt Creep on odd spot

Tain't fresh, and tain't marine! Talk about brackish setups.
Post Reply
LizB
Figure 8 Puffer
Posts: 138
Joined: Wed Feb 06, 2008 2:28 am

Salt Creep on odd spot

Post by LizB »

Hey guys, for some time I've been seeing salt creep on the bottom front of Harry's tank. It's where the wood and glass meet and it goes verticle a bit. There's also salt along the bottom of the glass on that side but it's horizontal. I don't remember, but I'm concerned that's the side I resealed last summer. I'll mark it if I ever reseal another tank.

Anyway, do you think this tank is getting ready to explode?

Thanks, Beth
User avatar
edmlfc1
Mbu Puffer
Posts: 2011
Joined: Sun Sep 09, 2007 5:03 pm
My Puffers: Elvis (Stars & Stripes) R.I.P. 9/11/11
125G:Fahaka (Annabelle)
Location (country): U.S.A.
Location: Texas

Re: Salt Creep on odd spot

Post by edmlfc1 »

I doubt it. For some reason I have salt creep on the front of my tank in the same place. It's probally from when we work in the tank water drips down to the trim and when it dries leaves salt creep. I would just watch my water level to see if the tank is leaking. :D Hope this eases your mind.
Need to know what kind of puffer you have? Click on Puffer ID.....Puffer ID: ug.php/v/PufferPedia/
What to feed your puffer? Click on Feeding......
Feeding: library/feeding/feeding-your-puffers/
Have a GSP, need more information......Click on GSP Article.....
GSP Article: library/puffers-in-focus/an-introductio ... d-puffers/
LizB
Figure 8 Puffer
Posts: 138
Joined: Wed Feb 06, 2008 2:28 am

Re: Salt Creep on odd spot

Post by LizB »

I dunno girl. I wipe it off and it comes back. I don't mess in Harry's tank at all until I clean it. It's an odd shaped tank and I hate the lid. A very OLD tank, they don't make them anymore. Besides that, Harry freaks out and tries his best to jump out everytime I start messing around the tank.

I sure hope you're right.

:D
edmlfc1 wrote:I doubt it. For some reason I have salt creep on the front of my tank in the same place. It's probally from when we work in the tank water drips down to the trim and when it dries leaves salt creep. I would just watch my water level to see if the tank is leaking. :D Hope this eases your mind.
User avatar
edmlfc1
Mbu Puffer
Posts: 2011
Joined: Sun Sep 09, 2007 5:03 pm
My Puffers: Elvis (Stars & Stripes) R.I.P. 9/11/11
125G:Fahaka (Annabelle)
Location (country): U.S.A.
Location: Texas

Re: Salt Creep on odd spot

Post by edmlfc1 »

I hope I'm right too. :D Could you possibly have some water dripping from the lid? My old tank had a weird lid and dew would build up on it and drip down the tank.
Need to know what kind of puffer you have? Click on Puffer ID.....Puffer ID: ug.php/v/PufferPedia/
What to feed your puffer? Click on Feeding......
Feeding: library/feeding/feeding-your-puffers/
Have a GSP, need more information......Click on GSP Article.....
GSP Article: library/puffers-in-focus/an-introductio ... d-puffers/
LizB
Figure 8 Puffer
Posts: 138
Joined: Wed Feb 06, 2008 2:28 am

Re: Salt Creep on odd spot

Post by LizB »

I really don't think that's what it is.

My 75gal is doing that and I'm about to go insane. I've got hard water deposits streaming all down the glass on that one side. It's dripping from under the wood. Vinegar isn't working to get the minerals off the glass and everytime I go check there's always a small stream of water. grrrrrr

I'm wondering if there's a real slow leak on Harry's tank. I keep debating on setting up the 43gal. I need a stand. I've never had water in it so I'd have to check it first. It's the one a friend drug out of the garbage about 20yrs ago. Really, I've had it that long and never had water or fish in it. My oldest moved his gerbils out of there recently.
edmlfc1 wrote:I hope I'm right too. :D Could you possibly have some water dripping from the lid? My old tank had a weird lid and dew would build up on it and drip down the tank.
LizB
Figure 8 Puffer
Posts: 138
Joined: Wed Feb 06, 2008 2:28 am

Re: alt Creep on odd spot

Post by LizB »

What did you do about that drip? This morn I put some silicone on it. I'm hoping the water level is low enough for the glass to stay dry so the silicone will work.

edmlfc1 wrote:I hope I'm right too. :D Could you possibly have some water dripping from the lid? My old tank had a weird lid and dew would build up on it and drip down the tank.
User avatar
Myaj
Tech Team
Posts: 4587
Joined: Sat Jun 04, 2005 12:27 pm
Gender: Female
My Puffers: Bubba, turgidus
Paris, lined burrfish
Location: SE Wisconsin
Contact:

Re: Salt Creep on odd spot

Post by Myaj »

Well, its either condensation forming up top and dripping down, or you dribble a little when you fill it at water change time, or its a slight leak.

What I would do, personally, is first fold up a paper towel and wedge it under the lid above this salt spot.. see if that paper town ends up wet or dry. If its wet, its probably coming from up there. If it stays dry, but your spot down below still shows up, it may have a slow leak.

I doubt even if its leaking that its getting ready to explode. I had a 29 with a weird plastic bottom to it that would release the silicone after a year or so. The weight of the water and gravel held it down and it never leaked, but every time I'd tear the tank down to change it or move or whatever, I'd have to reseal the bottom. I eventually threw it out because it was a pain in the rear...
Image
User avatar
Jase
Mbu Puffer
Posts: 1579
Joined: Sat Jan 12, 2008 3:13 am
Gender: Male
My Puffers: RIP Hootey :(
Location (country): USA
Location: Montana

Re: Salt Creep on odd spot

Post by Jase »

I have salt creep on mine too... I think mines a leak though, cause I don't dribble and the lid is sealed so no leak there...
-Jase
edmlfc1 wrote:A house without a puffer is not a home. :D
User avatar
edmlfc1
Mbu Puffer
Posts: 2011
Joined: Sun Sep 09, 2007 5:03 pm
My Puffers: Elvis (Stars & Stripes) R.I.P. 9/11/11
125G:Fahaka (Annabelle)
Location (country): U.S.A.
Location: Texas

Re: Salt Creep on odd spot

Post by edmlfc1 »

Just as Myaj said mine was condensation forming up top and dripping down. I just lowered the water level about 1/4" and it stopped.
Need to know what kind of puffer you have? Click on Puffer ID.....Puffer ID: ug.php/v/PufferPedia/
What to feed your puffer? Click on Feeding......
Feeding: library/feeding/feeding-your-puffers/
Have a GSP, need more information......Click on GSP Article.....
GSP Article: library/puffers-in-focus/an-introductio ... d-puffers/
Post Reply