RE-syliconeing a tank? HELP????

A place to discuss general puffer care or news.
Brandon8521
Fahaka Puffer
Posts: 824
Joined: Mon Feb 01, 2010 9:41 pm
Location (country): Usa

RE-syliconeing a tank? HELP????

Post by Brandon8521 »

Ok so i think there is something telling me that i dont need a 33 gallon brackish tank or something. I come home from school today to find my tank leaking from on of the corners midway down now mind you i have a flat-back hex so there is alot of corners. I have the tank emptied and and I cut out the sylicone on the parts that look ragged and old. I would love to hear ANY tips you guys can help me with. I baught the 100% clear silicone from homedepot since I have seen alot of of people use that on the DIY guides on youtube. They all said as long it is 100% sylicone it wont have the anti mildew stuff and additives and i read the tube it doesnt show any additives and states 100% sylicone.

I have my puffer in a plastic bin with some of the decore and and the heater and filter running on it.
User avatar
JoseDepacos
Green Spotted Puffer
Posts: 395
Joined: Sat Mar 27, 2010 3:18 pm
My Puffers: Valentini- Ripley
Location (country): USA

Re: RE-syliconeing a tank? HELP????

Post by JoseDepacos »

I personally have never tried to re-silicone a tank. I hate to sound discouraging but I have also never read of anyone successfully re-siliconing a tank. They always seem to continue leaking. I wish you the best of luck and hopefully someone here has some good advice on how to properly do this.
User avatar
Mezzovex
Figure 8 Puffer
Posts: 216
Joined: Sun Apr 04, 2010 5:39 am
Gender: Male
My Puffers: Dib the Fahaka
Location (country): United States, Oregon

Re: RE-syliconeing a tank? HELP????

Post by Mezzovex »

be smooth with it. dont stop mid way, only at the corners. and take your time. good luck!
Tanks I currently own:

125g freshwater tank w\ 30g sump, 840gph pump, ocean clear canister filter,
20" fire eel, and Dib the Fahaka

55g freshwater tank w\ Magnum 330 filter
Tigger the South American Puffer

5.5g nano saltwater tank
Clean up crew + coral + a strawberry dottyback
Brandon8521
Fahaka Puffer
Posts: 824
Joined: Mon Feb 01, 2010 9:41 pm
Location (country): Usa

Re: RE-syliconeing a tank? HELP????

Post by Brandon8521 »

Thanx for the hopefull wishes. Im almost done getting it all scraped up and cleaned. Ima make sure the inside is really sealed even if i have to go over every single seam again cause i dont have the money right now for a new tank and i really dont want to get rid of my poofer :( .
Ill take pics along the way so if it works it can be like a how to guide for people like me lol.
User avatar
J-P
Former Staff Member
Posts: 5626
Joined: Tue Oct 13, 2009 12:21 am
Gender: Male
Location (country): Japan
Location: Sasebo, Nagasaki, Japan

Re: RE-syliconeing a tank? HELP????

Post by J-P »

Dadof4 and I had a bantering back and forth about it in a thread of his but he deleted it.

I have done parts of my tank but not the entire thing. It was for cosmetic reasons
if you follow me, you avoid stepping in the crap that I just did...

https://www.youtube.com/channel/UCZR55G ... pqlgec1A2Q
Brandon8521
Fahaka Puffer
Posts: 824
Joined: Mon Feb 01, 2010 9:41 pm
Location (country): Usa

Re: RE-syliconeing a tank? HELP????

Post by Brandon8521 »

Im not doing the whole thing just the 4 visible corners not the very back ones. The bottom wasnt leaking that i know of (it still looks like clean sylicone.) I just cut it out the like i said the 4 corners and its definitaly not perdy but ill let yall know how the leak test goes tomorrow. I have no visible air bubble and i made sure its nice and tight to the glass then ran another beed over it without smoothing it out that much the second time. There was no drying inbetween running beeds so it should dry as one solid giant mass of sylicon lol. Hope it works cross your fingers for me.

I was going to post pics of the whole project but my wifes digi-cam sucks at really close up shot so its not really worth it.
User avatar
Pufferpunk
Queen Admin
Posts: 32988
Joined: Tue May 31, 2005 11:06 am
Gender: Female
My Puffers: Puffers I have kept:
T lineatus
T miurus
A modestus
T biocellatus
C valentini
C coranata
C papuan
C lorteti
DPs
suvattii
burrfish
T niphobles
Location (country): USA, Greenville, SC
Location: Greenville, SC
Contact:

Re: RE-syliconeing a tank? HELP????

Post by Pufferpunk »

Redo the entire tank. I have done several tanks. My friend had a bottle go through the front pane of his 125g & it lasted many years.
You are getting sleepy... you only hear the sound of my voice... you must do water changes... water changes... water changes... water changes...

"The solution to pollution is dilution!"
Brandon8521
Fahaka Puffer
Posts: 824
Joined: Mon Feb 01, 2010 9:41 pm
Location (country): Usa

Re: RE-syliconeing a tank? HELP????

Post by Brandon8521 »

Do you mean strip the sylicone from the entire tank and redo it? Or just run beads over the entire tank?

What i did was strip the sylicone from the 4 front corners and resylcone it i also ran a new beed over every existing corner from the inside of the tank but havnt re-ran all of outside ones just the ones i striped.
User avatar
Pufferpunk
Queen Admin
Posts: 32988
Joined: Tue May 31, 2005 11:06 am
Gender: Female
My Puffers: Puffers I have kept:
T lineatus
T miurus
A modestus
T biocellatus
C valentini
C coranata
C papuan
C lorteti
DPs
suvattii
burrfish
T niphobles
Location (country): USA, Greenville, SC
Location: Greenville, SC
Contact:

Re: RE-syliconeing a tank? HELP????

Post by Pufferpunk »

The entire thing. Be sure to get every last part of the silicone off the glass & clean all the surfaces to be re-glued with alcohol.
You are getting sleepy... you only hear the sound of my voice... you must do water changes... water changes... water changes... water changes...

"The solution to pollution is dilution!"
Brandon8521
Fahaka Puffer
Posts: 824
Joined: Mon Feb 01, 2010 9:41 pm
Location (country): Usa

Re: RE-syliconeing a tank? HELP????

Post by Brandon8521 »

Well since i have already dont what i have ima give it a leak test tomorrow and if it is sealed it will just have to do untill i have something more sefficient to home him in while i do a overhaul although i admit this whole thing is makeing me feel really nervous. Its almost worth it to trash it and try to find a 40 or something on craigslist.
Brandon8521
Fahaka Puffer
Posts: 824
Joined: Mon Feb 01, 2010 9:41 pm
Location (country): Usa

Re: RE-syliconeing a tank? HELP????

Post by Brandon8521 »

User avatar
Pufferpunk
Queen Admin
Posts: 32988
Joined: Tue May 31, 2005 11:06 am
Gender: Female
My Puffers: Puffers I have kept:
T lineatus
T miurus
A modestus
T biocellatus
C valentini
C coranata
C papuan
C lorteti
DPs
suvattii
burrfish
T niphobles
Location (country): USA, Greenville, SC
Location: Greenville, SC
Contact:

Re: RE-syliconeing a tank? HELP????

Post by Pufferpunk »

Your choice but remember--the folks building these tanks at the factory aren't rocket scientists... Probably don't even speak English. ;)
You are getting sleepy... you only hear the sound of my voice... you must do water changes... water changes... water changes... water changes...

"The solution to pollution is dilution!"
Brandon8521
Fahaka Puffer
Posts: 824
Joined: Mon Feb 01, 2010 9:41 pm
Location (country): Usa

Re: RE-syliconeing a tank? HELP????

Post by Brandon8521 »

Yah the only thing that really makes me nervous is im at school and i come home to 33 gallons of saltwater all over my living room :o . And the bill to pay for water damaged floors.
User avatar
PolishPuff
Mbu Puffer
Posts: 1212
Joined: Mon Oct 26, 2009 1:20 pm
Gender: Male
My Puffers: ________

Also cared for;

Fahaka------------------- Had to give it away
Auriglobus modestus-----Traded
Auriglobus silus ---------Died during transport.
Figure Eight Puffers -----Sold and or traded
Dwarf Puffers ------------Traded
Congo Puffer ------------Traded
South American Puffers -Traded
Carinotetraodon lorteti --Died under my supervision :(
Location (country): USA-Chicago, IL
Location: Chicago, IL

Re: RE-syliconeing a tank? HELP????

Post by PolishPuff »

Bcummings8521 wrote:Yah the only thing that really makes me nervous is im at school and i come home to 33 gallons of saltwater all over my living room :o . And the bill to pay for water damaged floors.
happened ones. Not 30+gal but only 20gal

scary.

when you see algae growing IN TO a silicone its time to re seal your tank.
"Lost time is never found again" Benjamin Franklin
Brandon8521
Fahaka Puffer
Posts: 824
Joined: Mon Feb 01, 2010 9:41 pm
Location (country): Usa

Re: RE-syliconeing a tank? HELP????

Post by Brandon8521 »

OK so i went outside and filled it 3/4 of the way up and no leaks right off the bat. ima let it sit for an hour or so just to make sure it doenst start anyleaks then im bringing that bad boy inside and get my puffer back to his home. Im excited but still a little nervouse. Im curiouse if adding all the extra weight from sand and decore will change anything.
Post Reply