Filter now obtained please help further

A place to discuss general puffer care or news.
Post Reply
User avatar
lilacamy931
Fahaka Puffer
Posts: 812
Joined: Sun Mar 22, 2009 7:15 am
My Puffers: 200 litre - waiting for a schoutedeni
Location (country): UK
Location: Bournemouth

Filter now obtained please help further

Post by lilacamy931 »

Well as you may or may not know, my cf1000 decided to spring a leak and so decided to get another filter (though couldnt quite afford the new prices). As it turned out the leak is incredibly slow but dont want to take chances, though will store it for now to use later. So I ended up with a XP3 and also a Eheim 2213 both second hand. I need help setting up to make sure I have smooth transition! So here they are:
Image

XP3 going on 100g.
The xp3 I think I have mostly covered, the tubes seem to fit snug onto the sockets without aid of any plugs. I can fit the adaptors and hopefully tubing from the cf1000 onto this one (fingers crossed). With the internals as this pic:
Image
There are gaps at the sides not snug fit, hope this is normal. each of the compartments have rings and sponge, should I transfer over rings and sponge from the cf1000 to seed properly into each of the containers and can sponge be put down the sides or not recommended?
Image
Quite short tubing thinking replacing if current fits how many size tubings are there? Do they need sockets?

Eheim to go on 120 litre, this appears to be full of sand so giving this and the other a good clean before anything else.
Inside is this which drags out a tube, can this be filled with whatever, it looks like bioballs in there but havent managed to get inside yet
Image
Here is the outlet tubes which look good working order with spray bar
Image
Here is the inlet tube - anyone guide me to the inlet parts? Anything I can adapt or where can go for parts?
Image
Lastly the tubes have these double attachments which somehow must fit onto the plumbing, how?! Stupid as I am, really cant figure out as to why there are two parts attached together or how to get them to fix on.
Image

Sorry for the doltiness. I want to get the xp3 up so no worries about flooding and the eheim up to eliminate the internal filter that does take up a lot of room in the triangular tank..Thanks so much for any help
RTR
Mentor
Posts: 6155
Joined: Tue May 31, 2005 4:39 pm
Gender: Male
Location (country): East Coast, USA

Re: Filter now obtained please help further

Post by RTR »

I can only respond re the Eheim, as that is the brand I use. The hard gray plastic device shown in the last photo is a shutoff/quick disconnect. There should be two such for each canister - one fits the return tubing from the canister top (also visible in the last photo) to the tank, the other splices into the tubing from the intake in the tank to the bottom fitting on the canister side. There are lock screwcaps to seal the tubing onto the quick disconnect assembly and at the canister base and top. My 2213s have different diameter intake and return hoses, and the disconnects are sized to match, The intake is larger than the return tubing (the intake is passive suction, the return is pumped). When the two valves making up the disconnect are both closed, the unit can be split with the release in the center of the unit with only a very small amount of water loss. This allows for easy transport of the separated canister for cleaning as required.

If the body of the canister houses only bioballs, it was used as bio-only canister, a technique I use routinely. There should not be any sand in the canister body. Be sure to rinse it all away before you try to assemble and even test the unit. Sand in the impeller core can destroy the impeller and even the canister drive by grinding out the impeller core/housing.

HTH
Where's the fish? - Neptune
User avatar
pufferpuggirl
Mbu Puffer
Posts: 3979
Joined: Mon Nov 03, 2008 3:04 pm
Gender: Female
My Puffers: Puffs & Stuff:

1 x M Abei
1 x M Turgidus
1 x T Palembangensis
1 x M Baileyii
1 x T Schoutedeni
1 x T Leiurus
1 x T Miurus
Rainbow crab
crayfish
Location (country): Yorkshire, GB
Location: South Yorkshire, UK

Re: Filter now obtained please help further

Post by pufferpuggirl »

I just wanted to say that I bought an Eheim external for my 58-gallon tank because of the reputation, but in hindsight I wish I hadn't. I don't know about anyone else, but I found it very difficult to set up.
For my 2 biggest tanks I bought a unknown brand of external filter and they have been the best yet. They both have a self-priming button on them making them so easy to get going.

Amy I hope you have an easier time setting up your Eheim than I did. Best of luck! :)
"Puffer .... man's best friend?"
User avatar
lilacamy931
Fahaka Puffer
Posts: 812
Joined: Sun Mar 22, 2009 7:15 am
My Puffers: 200 litre - waiting for a schoutedeni
Location (country): UK
Location: Bournemouth

Re: Filter now obtained please help further

Post by lilacamy931 »

Thanks very much RTR for the run down on the eheim, I was a bit surprised to see the sand when opened it but then again the eheim was thrown in with the filstar so cant complain too much ;) Going to have a crack at it today with those tips in mind (thank you) When you mention bio only filtration, I take it that is a good thing to do?

Thanks for the support Suzanne! We will see how we go, have downloaded manuals for each off the internet, the xp3 looks fairly easy as long as tubing fits, the eheim Im glad of RTR's comments as the manual found for the eheim was in german (though then again online translation..)


EDIT: One thing have realised, I havent tubing clamps for the plastic piping onto the unit, are these necessary?
User avatar
lilacamy931
Fahaka Puffer
Posts: 812
Joined: Sun Mar 22, 2009 7:15 am
My Puffers: 200 litre - waiting for a schoutedeni
Location (country): UK
Location: Bournemouth

Re: Filter now obtained please help further

Post by lilacamy931 »

Quick to add that the xp3 is up and running, think going to need xtra tubing to attach the eheim.
User avatar
Pufferpunk
Queen Admin
Posts: 32988
Joined: Tue May 31, 2005 11:06 am
Gender: Female
My Puffers: Puffers I have kept:
T lineatus
T miurus
A modestus
T biocellatus
C valentini
C coranata
C papuan
C lorteti
DPs
suvattii
burrfish
T niphobles
Location (country): USA, Greenville, SC
Location: Greenville, SC
Contact:

Re: Filter now obtained please help further

Post by Pufferpunk »

I use regular hose clamps.
You are getting sleepy... you only hear the sound of my voice... you must do water changes... water changes... water changes... water changes...

"The solution to pollution is dilution!"
User avatar
lilacamy931
Fahaka Puffer
Posts: 812
Joined: Sun Mar 22, 2009 7:15 am
My Puffers: 200 litre - waiting for a schoutedeni
Location (country): UK
Location: Bournemouth

Re: Filter now obtained please help further

Post by lilacamy931 »

Thanks for that Pufferpunk (writes on fishy shopping list :) )

One further thing to ask is on the 6th picture down, shows the intake, and hoping I am right in that it is the wrong way round and the curved bit connected to the piping and the long green bit goes in the tank to draw water out, is this right and also can I get away without a strainer for a short time as the fish I am going for just wouldnt be able to fit up there?

With the xp3 for those that have these or similar, does the water go right to the top of the canister>?

A big thanks for all the help, do apologise.
User avatar
pufferpuggirl
Mbu Puffer
Posts: 3979
Joined: Mon Nov 03, 2008 3:04 pm
Gender: Female
My Puffers: Puffs & Stuff:

1 x M Abei
1 x M Turgidus
1 x T Palembangensis
1 x M Baileyii
1 x T Schoutedeni
1 x T Leiurus
1 x T Miurus
Rainbow crab
crayfish
Location (country): Yorkshire, GB
Location: South Yorkshire, UK

Re: Filter now obtained please help further

Post by pufferpuggirl »

The thing I would worry about with not using a strainer, would be having bigger pieces of debris going up and clogging up your filter.
"Puffer .... man's best friend?"
User avatar
lilacamy931
Fahaka Puffer
Posts: 812
Joined: Sun Mar 22, 2009 7:15 am
My Puffers: 200 litre - waiting for a schoutedeni
Location (country): UK
Location: Bournemouth

Re: Filter now obtained please help further

Post by lilacamy931 »

Ah no worries, I have book marked some strainers in case the store dont have them. When it comes to equipment I always have lots to learn.
User avatar
lilacamy931
Fahaka Puffer
Posts: 812
Joined: Sun Mar 22, 2009 7:15 am
My Puffers: 200 litre - waiting for a schoutedeni
Location (country): UK
Location: Bournemouth

Re: Filter now obtained please help further

Post by lilacamy931 »

Further problem cant fix the water level problem, took the sponge out redid and when turned on the water decreased and made a noise, put my extra bit back in and it was working again with a water level like this:
Image
RTR
Mentor
Posts: 6155
Joined: Tue May 31, 2005 4:39 pm
Gender: Male
Location (country): East Coast, USA

Re: Filter now obtained please help further

Post by RTR »

The Eheim classics are not user-friendly. If you want/need the bells and whistles, it is not the filter for you. If you want a workhorse that will operate very economically for >30 years, it just may be the unit for you.

I use biofiltration-only canisters primarily in FW. Biofiltration in SW is needed only in FO tanks. Other SW setups would use live rock, a plenum or DSB, and/or a 24/y lighted macroalgae refugium rather than bacterial biofiltration. All my FW bio-only filters are Erheim classics with bioballs only and in-tank sponge prefilters. I have a dozen or so of those operating full-time, the oldest date back into the late 80s to easty 90's, the youngest ~10 years old - none has ever been any problem at all. They are the ultimate protected self-cleaning biofilters IMHO and IME. I don't have any small tanks operating ATM, but have used them down to 10 gallons US. The small tanks had the smallest Classics of course. I don't know how you plan to use your unit. If I were doing mechanical filtration, I would use a more user-friendly unit.

Eheims have their own hose claps built-in on the canisters and quick release valve sets, so they need no additional clamps. Cable-tie type clamps do tend to make Eheim tubing leak for me, so i never use those on it. Eheim tubing lasts about 10 years for me. Once it starts getting hard and inelastic I do replace it.

HTH
Where's the fish? - Neptune
User avatar
lilacamy931
Fahaka Puffer
Posts: 812
Joined: Sun Mar 22, 2009 7:15 am
My Puffers: 200 litre - waiting for a schoutedeni
Location (country): UK
Location: Bournemouth

Re: Filter now obtained please help further

Post by lilacamy931 »

Thanks very much for that RTR, Im learning every step of the way - promise! :) I dont think I will have the option of the Eheim as tried to get it working (not on the tank) but for a test run and the motor head doesnt appear to work when plugged in unless I am doing something very wrong. Will give another go in short while but this may be best kept in storage for now..
Post Reply