Water change / filter question

A place to discuss general puffer care or news.
asianpuffer
Figure 8 Puffer
Posts: 229
Joined: Fri Oct 23, 2009 3:52 pm
My Puffers: 38 Gallon Tank
** 3 SAP's
Location (country): AZ

Water change / filter question

Post by asianpuffer »

I was just curious what I am supposed to do with the eheim cannister filter when I am only only a water change. After changing the water, do I just plug the unit back in? i noticed that when i did this, a whole bunch of bubbles were coming out due to air. do I need do something to prevent this? empty the cannister of its water?
User avatar
Hilly
Mentor
Posts: 1903
Joined: Sun Jan 15, 2006 6:36 pm
Gender: Male
My Puffers: Current: Tetraodon Lineatus
Previous:
Tetraodon Sabahensis
Montrete Abei
Tetraodon Biocellatus
Carinotetraodon Salivator
Location (country): UK
Location: Nottinghamshire, UK

Re: Water change / filter question

Post by Hilly »

Never empty mine unless I am cleaning it out. I unplug it and plug it back in after the change and it starts up again. Sometimes I have left it on whilst draining down and refilling with a python. Edit: my spraybar points directly down though, probably not a great idea to do that if its pointing any other way.
Hilly
User avatar
soggydrysuit
Fahaka Puffer
Posts: 541
Joined: Sun Jan 13, 2008 7:36 am
Gender: Male
My Puffers: 2x T.fluviatilis
1x C. irrubesco
2 x T. nigroviridis
1 x T. ocellatus
Current non-puffers:

Enough for people to think I'm a loonie :-)
Location (country): UK
Location: Durham, UK

Re: Water change / filter question

Post by soggydrysuit »

Hi there,

Do you have any taps or valves between the filter and the tank? Most externals do. If so, just turn off the filter then shut the valves and do your water change. When the tank is full again, open the valves then turn the power on.

If not, I'd try to stop the ends of the hoses with something non toxic to fish.

I have a fluval 404 external, with valves and it's a total nightmare to get the air out after cleaning the pads. I have to start with the thing on it's side and raise it to vertical incrementally. That's when the filter 'bucket' is full of water!

HTH
asianpuffer
Figure 8 Puffer
Posts: 229
Joined: Fri Oct 23, 2009 3:52 pm
My Puffers: 38 Gallon Tank
** 3 SAP's
Location (country): AZ

Re: Water change / filter question

Post by asianpuffer »

Hilly wrote:Never empty mine unless I am cleaning it out. I unplug it and plug it back in after the change and it starts up again. Sometimes I have left it on whilst draining down and refilling with a python. Edit: my spraybar points directly down though, probably not a great idea to do that if its pointing any other way.
DO i need to fill any of the tubes with water? the intake and outtake both have caps which you can uncap and fill with water.. is this what it is for?
User avatar
Hilly
Mentor
Posts: 1903
Joined: Sun Jan 15, 2006 6:36 pm
Gender: Male
My Puffers: Current: Tetraodon Lineatus
Previous:
Tetraodon Sabahensis
Montrete Abei
Tetraodon Biocellatus
Carinotetraodon Salivator
Location (country): UK
Location: Nottinghamshire, UK

Re: Water change / filter question

Post by Hilly »

I am unsure abot the caps but I wouldn't have thought there is a significance between the pro 3 which you have and the pro 2 which I have as your model is my direct replacement. When you first got it did you have to use these caps for priming the filter.
Hilly
asianpuffer
Figure 8 Puffer
Posts: 229
Joined: Fri Oct 23, 2009 3:52 pm
My Puffers: 38 Gallon Tank
** 3 SAP's
Location (country): AZ

Re: Water change / filter question

Post by asianpuffer »

soggydrysuit wrote:Hi there,

Do you have any taps or valves between the filter and the tank? Most externals do. If so, just turn off the filter then shut the valves and do your water change. When the tank is full again, open the valves then turn the power on.

If not, I'd try to stop the ends of the hoses with something non toxic to fish.

I have a fluval 404 external, with valves and it's a total nightmare to get the air out after cleaning the pads. I have to start with the thing on it's side and raise it to vertical incrementally. That's when the filter 'bucket' is full of water!

HTH
No taps or values. I do notice that when i am changing the water and the water line drops below the intake, water from the tube gets drained.
asianpuffer
Figure 8 Puffer
Posts: 229
Joined: Fri Oct 23, 2009 3:52 pm
My Puffers: 38 Gallon Tank
** 3 SAP's
Location (country): AZ

Re: Water change / filter question

Post by asianpuffer »

No. the 3 came with the upgraded install kits for the intake and outtakes (no green intake or spraybar).
Hilly wrote:I am unsure abot the caps but I wouldn't have thought there is a significance between the pro 3 which you have and the pro 2 which I have as your model is my direct replacement. When you first got it did you have to use these caps for priming the filter.
User avatar
Iliveinazoo
Fahaka Puffer
Posts: 826
Joined: Thu Jul 17, 2008 8:09 am
Gender: Male
My Puffers: 1xFigure 8
Location (country): UK
Location: Southampton

Re: Water change / filter question

Post by Iliveinazoo »

I'm not familiar with the Eheim but if it fills back up with water (primes itself) within a couple of seconds of turning it on then I wouldn't worry about it, if it stays really loud then air is trapped in it and you will have to re-prime it before turning it back on.
asianpuffer
Figure 8 Puffer
Posts: 229
Joined: Fri Oct 23, 2009 3:52 pm
My Puffers: 38 Gallon Tank
** 3 SAP's
Location (country): AZ

Re: Water change / filter question

Post by asianpuffer »

Iliveinazoo wrote:I'm not familiar with the Eheim but if it fills back up with water (primes itself) within a couple of seconds of turning it on then I wouldn't worry about it, if it stays really loud then air is trapped in it and you will have to re-prime it before turning it back on.
Well once i change the water, the water goes below the water line causing the water from the intake tube to come out. When I plug the unit back in, its not loud but lots of air bubbles do come out.
User avatar
Iliveinazoo
Fahaka Puffer
Posts: 826
Joined: Thu Jul 17, 2008 8:09 am
Gender: Male
My Puffers: 1xFigure 8
Location (country): UK
Location: Southampton

Re: Water change / filter question

Post by Iliveinazoo »

So if the bubbles keep on coming out for longer than a few seconds then you should prime it before switching it back on
User avatar
jdak
Green Spotted Puffer
Posts: 408
Joined: Sun Feb 21, 2010 2:25 pm
Gender: Male
My Puffers: Stars & stripes
Location (country): USA

Re: Water change / filter question

Post by jdak »

Give the canister a light shake. That will knock the rest of the bubbles out.
Check out my puffer, video, and tanks @ jdak.net.
46g reef
150g FO
asianpuffer
Figure 8 Puffer
Posts: 229
Joined: Fri Oct 23, 2009 3:52 pm
My Puffers: 38 Gallon Tank
** 3 SAP's
Location (country): AZ

Re: Water change / filter question

Post by asianpuffer »

how would you reprime the eheim afterwards? do you empty all the water out of the cannister?
Brandon8521
Fahaka Puffer
Posts: 824
Joined: Mon Feb 01, 2010 9:41 pm
Location (country): Usa

Re: Water change / filter question

Post by Brandon8521 »

asianpuffer wrote:
Hilly wrote:Never empty mine unless I am cleaning it out. I unplug it and plug it back in after the change and it starts up again. Sometimes I have left it on whilst draining down and refilling with a python. Edit: my spraybar points directly down though, probably not a great idea to do that if its pointing any other way.
DO i need to fill any of the tubes with water? the intake and outtake both have caps which you can uncap and fill with water.. is this what it is for?
Are these caps on the ends that are in the tank? If so then turn it off and cap them b4 you take any water out and uncap them and turn it on after your done. then it shouldnt have a way to drain any water and stay a closed system dureing the whole process. (thats if im understanding you correctly)
asianpuffer
Figure 8 Puffer
Posts: 229
Joined: Fri Oct 23, 2009 3:52 pm
My Puffers: 38 Gallon Tank
** 3 SAP's
Location (country): AZ

Re: Water change / filter question

Post by asianpuffer »

Bcummings8521 wrote:
asianpuffer wrote:
Hilly wrote:Never empty mine unless I am cleaning it out. I unplug it and plug it back in after the change and it starts up again. Sometimes I have left it on whilst draining down and refilling with a python. Edit: my spraybar points directly down though, probably not a great idea to do that if its pointing any other way.
DO i need to fill any of the tubes with water? the intake and outtake both have caps which you can uncap and fill with water.. is this what it is for?
Are these caps on the ends that are in the tank? If so then turn it off and cap them b4 you take any water out and uncap them and turn it on after your done. then it shouldnt have a way to drain any water and stay a closed system dureing the whole process. (thats if im understanding you correctly)
The caps are on top of the tank on both the intakes and outtakes
User avatar
Pufferpunk
Queen Admin
Posts: 32988
Joined: Tue May 31, 2005 11:06 am
Gender: Female
My Puffers: Puffers I have kept:
T lineatus
T miurus
A modestus
T biocellatus
C valentini
C coranata
C papuan
C lorteti
DPs
suvattii
burrfish
T niphobles
Location (country): USA, Greenville, SC
Location: Greenville, SC
Contact:

Re: Water change / filter question

Post by Pufferpunk »

I find as long as the water level doesn't go below the intake tube while the filter is on, I don't need to prime it before turning it on. otherwise, just turn off the filter during the WC & turn it back on after the tank is full. I have all my filters plugged into a strip, so I can just flip a switch to turn them off & on. To prime the Eheim, you must fill to the top with water.
You are getting sleepy... you only hear the sound of my voice... you must do water changes... water changes... water changes... water changes...

"The solution to pollution is dilution!"
Post Reply