Tank Cover

A place to discuss general puffer care or news.
Post Reply
asianpuffer
Figure 8 Puffer
Posts: 229
Joined: Fri Oct 23, 2009 3:52 pm
My Puffers: 38 Gallon Tank
** 3 SAP's
Location (country): AZ

Tank Cover

Post by asianpuffer »

Hello everyone,

I was able to get my hands on the Marineland Double Bright LED Light Fixture for FREE!!!

Now my only concern is that I would need a top for my aquarium now.

Any ideas? I thought about eggcrate but was worried that the fish would spalsh water outside the tank.

Also does anyone have this lighting setup? Any reviews on them?

THANKS!
User avatar
Hilly
Mentor
Posts: 1903
Joined: Sun Jan 15, 2006 6:36 pm
Gender: Male
My Puffers: Current: Tetraodon Lineatus
Previous:
Tetraodon Sabahensis
Montrete Abei
Tetraodon Biocellatus
Carinotetraodon Salivator
Location (country): UK
Location: Nottinghamshire, UK

Re: Tank Cover

Post by Hilly »

You've got a few options, get some glass cut and some runners or just some clear perspex or acrylic sheet cut to size to put over the top. Anything to stop condensation or water splash getting onto it and potentially causing an electrical short.
Hilly
asianpuffer
Figure 8 Puffer
Posts: 229
Joined: Fri Oct 23, 2009 3:52 pm
My Puffers: 38 Gallon Tank
** 3 SAP's
Location (country): AZ

Re: Tank Cover

Post by asianpuffer »

Hilly wrote:You've got a few options, get some glass cut and some runners or just some clear perspex or acrylic sheet cut to size to put over the top. Anything to stop condensation or water splash getting onto it and potentially causing an electrical short.

So the eggcrate would be a bad idea then right?
User avatar
Hilly
Mentor
Posts: 1903
Joined: Sun Jan 15, 2006 6:36 pm
Gender: Male
My Puffers: Current: Tetraodon Lineatus
Previous:
Tetraodon Sabahensis
Montrete Abei
Tetraodon Biocellatus
Carinotetraodon Salivator
Location (country): UK
Location: Nottinghamshire, UK

Re: Tank Cover

Post by Hilly »

Just my opinion but too many holes for condensation and splashing to get through.
Hilly
asianpuffer
Figure 8 Puffer
Posts: 229
Joined: Fri Oct 23, 2009 3:52 pm
My Puffers: 38 Gallon Tank
** 3 SAP's
Location (country): AZ

Re: Tank Cover

Post by asianpuffer »

Hilly wrote:Just my opinion but too many holes for condensation and splashing to get through.
would i just cut a rectangle sized one or one that is cut around all the filter tubes etc...

is there a company that specializes in this?
User avatar
Hilly
Mentor
Posts: 1903
Joined: Sun Jan 15, 2006 6:36 pm
Gender: Male
My Puffers: Current: Tetraodon Lineatus
Previous:
Tetraodon Sabahensis
Montrete Abei
Tetraodon Biocellatus
Carinotetraodon Salivator
Location (country): UK
Location: Nottinghamshire, UK

Re: Tank Cover

Post by Hilly »

Up to you really, If your filter pipes are situated at either end of the tank just cut the edge off at an agle so it bypasses the pipework. Although you want it to cover the top you dont want it too tight fitting for gaseous exchange to take place and if you have cuts at the edge and your lighting will be situated centre of the tank it will pretty much rule out getting water on it. I would follow the manufacturers guidelines on distance from the top of the water for the lighting unit as well.

Specialized company for glass cutting???? Any place that supplies glass should be able to cut you some pieces for the top. It doesnt have to be thick like the tank walls, thin glass will be fine 3-6mm. Acrylic sheets or perspex you could cut yourself or ask the supplier to cut it to size and take an angled notch off each corner.

Edit: forgot if you have any LFS that build their own tanks give them your tank dimensions and glass thickness and they willbe able to cut you glass for the lid also. Worth measuring the internal dimensions to be doubley sure.
Hilly
asianpuffer
Figure 8 Puffer
Posts: 229
Joined: Fri Oct 23, 2009 3:52 pm
My Puffers: 38 Gallon Tank
** 3 SAP's
Location (country): AZ

Re: Tank Cover

Post by asianpuffer »

so i went to the glass shop and gave him the dimensions and told him i needed 2 1inch holes drilled in them as well. The sheet of glass would have been 36" by 9" roughly. He estimated $50. :-(

Does this seem resonable?
User avatar
Hilly
Mentor
Posts: 1903
Joined: Sun Jan 15, 2006 6:36 pm
Gender: Male
My Puffers: Current: Tetraodon Lineatus
Previous:
Tetraodon Sabahensis
Montrete Abei
Tetraodon Biocellatus
Carinotetraodon Salivator
Location (country): UK
Location: Nottinghamshire, UK

Re: Tank Cover

Post by Hilly »

It will be the drilling thats costing the money there. Seems a very lot for a tank cover especially of that size. No way would I pay that converted I think it would be more like $15-20 max for a cover over here. Perhaps a cheap DIY plastic version would be better for you as that price is far too much. Does it need to be drilled. for the pipes to pass, ill get you a pic of my tank lid later so you can have a look at what I mean.
Hilly
asianpuffer
Figure 8 Puffer
Posts: 229
Joined: Fri Oct 23, 2009 3:52 pm
My Puffers: 38 Gallon Tank
** 3 SAP's
Location (country): AZ

Re: Tank Cover

Post by asianpuffer »

yeah the photo would help. thanks

And i believe it would have to be drilled. I have a filstar xp3 so i have 2 pipes that come out...
asianpuffer
Figure 8 Puffer
Posts: 229
Joined: Fri Oct 23, 2009 3:52 pm
My Puffers: 38 Gallon Tank
** 3 SAP's
Location (country): AZ

Re: Tank Cover

Post by asianpuffer »

i found this..maybe i should go this route?
http://www.fosterandsmithaquatics.com/p ... catid=3790
User avatar
Hilly
Mentor
Posts: 1903
Joined: Sun Jan 15, 2006 6:36 pm
Gender: Male
My Puffers: Current: Tetraodon Lineatus
Previous:
Tetraodon Sabahensis
Montrete Abei
Tetraodon Biocellatus
Carinotetraodon Salivator
Location (country): UK
Location: Nottinghamshire, UK

Re: Tank Cover

Post by Hilly »

If thats going to be the cheaper option for you and it will fit your tank then go for it.
This is what I was meaning with the glass.
Notch cut out thecorner allowing external pipeworkto go through. Please excusethe poor quality pics.
Image
Image
Image
Hilly
Post Reply