Filstar XP3

A place to discuss general puffer care or news.
asianpuffer
Figure 8 Puffer
Posts: 229
Joined: Fri Oct 23, 2009 3:52 pm
My Puffers: 38 Gallon Tank
** 3 SAP's
Location (country): AZ

Re: Filstar XP3

Post by asianpuffer »

Hilly wrote:Yes just rinse it out, if it starts to fall apart then replace it.
Yes once a month should be fine, I doubt with that bioload in the tank and what the XP3 is rated for you will see any decrease in flow.
Thank you Hilly, Myaj and Flutter for all your input.

How often should I chance the stars and the ceramic rings I put in from my old filter?
User avatar
Myaj
Tech Team
Posts: 4587
Joined: Sat Jun 04, 2005 12:27 pm
Gender: Female
My Puffers: Bubba, turgidus
Paris, lined burrfish
Location: SE Wisconsin
Contact:

Re: Filstar XP3

Post by Myaj »

You don't really change the ceramic ones. I mean, technically, they get "plugged up" over time, and you could take some out and boil them to steam clean them (never all at once).. but these are permanent "media". I never bother with anything more than a rinse, myself.

Are the "stars" ceramic or do you mean the foam thingies? If they are foam, just rinse and reuse, no need to do more than that unless they fall apart over time.
Image
asianpuffer
Figure 8 Puffer
Posts: 229
Joined: Fri Oct 23, 2009 3:52 pm
My Puffers: 38 Gallon Tank
** 3 SAP's
Location (country): AZ

Re: Filstar XP3

Post by asianpuffer »

Got it.
Now that Im not using the AC70, the top of the aquarium is left with floating dust sheets...anyway to get rid of this?
Would a airstone help?
User avatar
Hilly
Mentor
Posts: 1903
Joined: Sun Jan 15, 2006 6:36 pm
Gender: Male
My Puffers: Current: Tetraodon Lineatus
Previous:
Tetraodon Sabahensis
Montrete Abei
Tetraodon Biocellatus
Carinotetraodon Salivator
Location (country): UK
Location: Nottinghamshire, UK

Re: Filstar XP3

Post by Hilly »

Do you mean like a scummy film of dust on top of the water An airstone might speed it up and cause the dust to sink by agitating the water surface more, it should go in time anyway on its own with water changes.
Hilly
Nick
Former Staff Member
Posts: 3231
Joined: Sun Oct 22, 2006 8:47 pm
My Puffers: Mine:
GSPs - Shakespeare and Jillybean
F8 - Velvet
My fiance:
DP - Emma Goldman
Narrow Lined Puffer - Ulrike
Location (country): Northeastern USA
Location: Middletown, CT
Contact:

Re: Filstar XP3

Post by Nick »

Not enough agitation on the surface form the water returning to the tank from the filter.

http://www.amazon.com/KOLLER-CRAFT-Surf ... B00176MUKY

Will continually skim the waters surface to increase 02 moving into the tank from the air above. If you are creative, you can find a way to attach it to most filters.
No matter how magnificent your successes or devastating your failures, the worlds' approximately 5 billion impoverished people could not possibly care less.
asianpuffer
Figure 8 Puffer
Posts: 229
Joined: Fri Oct 23, 2009 3:52 pm
My Puffers: 38 Gallon Tank
** 3 SAP's
Location (country): AZ

Re: Filstar XP3

Post by asianpuffer »

ok so i repositioned the spraybar about 1 cm above water level. Now there are tiny bubbles everywhere from the spraybar hitting the water...stupid question but is that normal?
Nick
Former Staff Member
Posts: 3231
Joined: Sun Oct 22, 2006 8:47 pm
My Puffers: Mine:
GSPs - Shakespeare and Jillybean
F8 - Velvet
My fiance:
DP - Emma Goldman
Narrow Lined Puffer - Ulrike
Location (country): Northeastern USA
Location: Middletown, CT
Contact:

Re: Filstar XP3

Post by Nick »

Yes. You can reposition so it does not cause bubbling, so long as it agitates the surface water such that good oxygen exchange can take place.
No matter how magnificent your successes or devastating your failures, the worlds' approximately 5 billion impoverished people could not possibly care less.
User avatar
J-P
Former Staff Member
Posts: 5626
Joined: Tue Oct 13, 2009 12:21 am
Gender: Male
Location (country): Japan
Location: Sasebo, Nagasaki, Japan

Re: Filstar XP3

Post by J-P »

that will work for a few days until you have evap and it makes bubble again ;)

just my opinion, try to position it so that when it creates bubbles after a week, you'll know when to do your water changes ;) I measured my pumps with a strip of painter's tape when the tank was full and again 1 week later. I positioned almost everything at the 1 week level. Once the pumps started foaming I knew I had a water change due. :)
if you follow me, you avoid stepping in the crap that I just did...

https://www.youtube.com/channel/UCZR55G ... pqlgec1A2Q
User avatar
Flutter
Former Staff Member
Posts: 2938
Joined: Wed Nov 18, 2009 5:43 pm
Location (country): Canada

Re: Filstar XP3

Post by Flutter »

I top up the tank every day :lol: My spraybar is about 2" under the surface and provides a nice surface current.
It is absurd to talk of one animal being higher than another. We consider those, when the cerebral structure/intellectual faculties most developed, as highest. A bee doubtless would when the instincts were.
Charles Darwin
asianpuffer
Figure 8 Puffer
Posts: 229
Joined: Fri Oct 23, 2009 3:52 pm
My Puffers: 38 Gallon Tank
** 3 SAP's
Location (country): AZ

Re: Filstar XP3

Post by asianpuffer »

When i had the bar one inch below the water line, the top of the surface would not get any movement. How are you getting surface movement with the bar being under 2"
User avatar
J-P
Former Staff Member
Posts: 5626
Joined: Tue Oct 13, 2009 12:21 am
Gender: Male
Location (country): Japan
Location: Sasebo, Nagasaki, Japan

Re: Filstar XP3

Post by J-P »

depends on the angle
if you follow me, you avoid stepping in the crap that I just did...

https://www.youtube.com/channel/UCZR55G ... pqlgec1A2Q
User avatar
Flutter
Former Staff Member
Posts: 2938
Joined: Wed Nov 18, 2009 5:43 pm
Location (country): Canada

Re: Filstar XP3

Post by Flutter »

Weird. Ours is directly at horizontal and provides enough surface current to provide oxygen to the fish (which are currently all bottom dwellers) with the addition of CO2. We actually get so much surface current that it needs to be turned off for feeding.
It is absurd to talk of one animal being higher than another. We consider those, when the cerebral structure/intellectual faculties most developed, as highest. A bee doubtless would when the instincts were.
Charles Darwin
asianpuffer
Figure 8 Puffer
Posts: 229
Joined: Fri Oct 23, 2009 3:52 pm
My Puffers: 38 Gallon Tank
** 3 SAP's
Location (country): AZ

Re: Filstar XP3

Post by asianpuffer »

On another note...

Ever since i switched over from my AC 70 to my xp3, my nitrate levels have been really low..Before the nitrate level would be around 10-20 or so after a few days of a water change.. Now with this filter when I test the water I get 0, 0 and 0-10 for the nitrate levels...I used the ceramic balls from the ac unit along with the stars the new unit came with.

Is this normal?
Post Reply