I may've found a very cheap way to get a 1200UKgallon tank!

A place to discuss general puffer care or news.
User avatar
puffertt77
Suspended
Posts: 822
Joined: Thu Feb 05, 2009 8:19 pm
My Puffers: Mbu Puffer named Naboo
South American Puffer named Bollo RIP :(
3 Dwarf Puffers yet to be named
Red Eye Red Tailed Puffer - Returned to LFS for being to vicious
Porky the Porcupine
Pup the Dogface
Location: London

I may've found a very cheap way to get a 1200UKgallon tank!

Post by puffertt77 »

Hello All

I've just been on ...wait for it...yes you've guest it Ebay.co.uk and I've found a company that builds garden fish ponds out of big fibre glass parts. When I say fish ponds they are actually tanks which they either sink into the ground or can be stood above ground.

Here's the link to their tanks on Ebay.co.uk
http://cgi.ebay.co.uk/ws/eBayISAPI.dll? ... 2759.l1259
Here's their website
http://www.kcrcomposite.co.uk

I've emailed them and asked them if it would be possible to install a glass/acrylic panel in the front of one.

I cannot see why this would not be achieveable in some way.

I'm hoping they have smaller square panels that they use to build the tank with, maybe half or a quarter of the size of the ones that can be seen in their image of the tank. That way the front could have a frame built with these smaller panels. Either down the left side of the front, along the bottom of the front and then up the right of the front. And if possible across the top of the front to make a frame.

Then like a plywood tank the glass/acrylic pane could be placed behind ythis in the tank and sealed with a lot of sylicone.

If this is possible it won't cost much more than they're selling it for now which is £460/$656 for a 10ft w x 4ft d x 4ft h, 1200ukgallon/1441usgallon tank built in your house by them!

Of course the glass/acrylic price will have to be added on and I'm not yet sure if it's possible for them to be able to do it but it seems possible to me

Even if they cannot it's tempting to just buy one of their tanks for £460 and try and do it myself

What do you think?

Any sugestions?
Image Image
User avatar
Jase
Mbu Puffer
Posts: 1579
Joined: Sat Jan 12, 2008 3:13 am
Gender: Male
My Puffers: RIP Hootey :(
Location (country): USA
Location: Montana

Re: I may've found a very cheap way to get a 1200UKgallon tank!

Post by Jase »

Sounds cool, but I'd not try a DIY with that much water and pressure... or maybe you are more experience with building than me...
be neat if they can do it though :)
-Jase
edmlfc1 wrote:A house without a puffer is not a home. :D
User avatar
puffertt77
Suspended
Posts: 822
Joined: Thu Feb 05, 2009 8:19 pm
My Puffers: Mbu Puffer named Naboo
South American Puffer named Bollo RIP :(
3 Dwarf Puffers yet to be named
Red Eye Red Tailed Puffer - Returned to LFS for being to vicious
Porky the Porcupine
Pup the Dogface
Location: London

Re: I may've found a very cheap way to get a 1200UKgallon tank!

Post by puffertt77 »

Jase wrote:Sounds cool, but I'd not try a DIY with that much water and pressure... or maybe you are more experience with building than me...
be neat if they can do it though :)
No I'm not experienced with building to be honest but I've been doing a lot of research and I'm sure I could find a way, I'd rather attempt this than build the whole thing out of plywood then epoxy it and layer it in fibre glass and then paint more epoxy on it and so on.

Here's their pic of the front
pond tank.JPG
The blue is the glass which would cover the full 10ft w x 4ft h front to the tank
pond tank2.jpg
The frame may need to be a lot thicker
You do not have the required permissions to view the files attached to this post.
Image Image
Camaro95
Figure 8 Puffer
Posts: 117
Joined: Sat Dec 08, 2007 2:19 am
My Puffers: 3 dwarf puffers
Location: Ontario

Re: I may've found a very cheap way to get a 1200UKgallon tank!

Post by Camaro95 »

I wouldn't try doctoring their tanks, that's just a waste of good money if it fails. Too much risk. Though instead of siliconing it, you could just use the fibre glass put/gel that you can get at hardware stores to seal the glass piece to one end. It would be quite a bit stronger than simple silicone.

You could always buy one and use it as an indoor pond for your fish. just make sure you have real good lighting and maybe a platform or bridge over it so you can look down into it.
User avatar
puffertt77
Suspended
Posts: 822
Joined: Thu Feb 05, 2009 8:19 pm
My Puffers: Mbu Puffer named Naboo
South American Puffer named Bollo RIP :(
3 Dwarf Puffers yet to be named
Red Eye Red Tailed Puffer - Returned to LFS for being to vicious
Porky the Porcupine
Pup the Dogface
Location: London

Re: I may've found a very cheap way to get a 1200UKgallon tank!

Post by puffertt77 »

Camaro95 wrote:I wouldn't try doctoring their tanks, that's just a waste of good money if it fails.
Very true, I'm hoping they'll come up with a solution, looking at their website it seems they're able to do quite a lot
Camaro95 wrote:Though instead of siliconing it, you could just use the fibre glass put/gel that you can get at hardware stores to seal the glass piece to one end. It would be quite a bit stronger than simple silicone.
Yeah maybe although I've read that alot of people who have built massive plywood tanks have just used sylicone to seal the front because the pressure from the water keeps the glass sealed to the front of the tank

Thanks for the ideas
Image Image
User avatar
flash.dan
Green Spotted Puffer
Posts: 433
Joined: Fri Aug 22, 2008 9:50 am
My Puffers: 8 years of FW puffer care!
currently have 1x mbu
Bubba 17" gentle giant... loves a belly tickle.
2x Suvatti Pair
1x Carinotetraodon borneensis
Location: Coventry, UK

Re: I may've found a very cheap way to get a 1200UKgallon tank!

Post by flash.dan »

a 10x4 peice of 25mm cast will cost you about £1400 maybe more. Usually with diy tanks i would only reccomend using the same material that have known properties. fiberglass and acrylic / glass may not go well.
User avatar
puffertt77
Suspended
Posts: 822
Joined: Thu Feb 05, 2009 8:19 pm
My Puffers: Mbu Puffer named Naboo
South American Puffer named Bollo RIP :(
3 Dwarf Puffers yet to be named
Red Eye Red Tailed Puffer - Returned to LFS for being to vicious
Porky the Porcupine
Pup the Dogface
Location: London

Re: I may've found a very cheap way to get a 1200UKgallon tank!

Post by puffertt77 »

flash.dan wrote:a 10x4 peice of 25mm cast will cost you about £1400 maybe more. Usually with diy tanks i would only recomend using the same material that have known properties. fiberglass and acrylic / glass may not go well.
I have a contact that can build a 10ft w x 4 ft d x 2ft h for £927 and they recomended 15mm thick glass, I'm sure I could ask to buy the bottom piece of that tanks pain of glass which would measure the 10ft x 4ft I need. Should only cost a few hundred if the whole tank costs £927 built on site. The same guys said any tank they build that's 4ft heigh will cost £5000+!

Maybe your right though with going with the thicker glass. Also even if this doesn't work out I'll still have to buy the glass/acrylic for a Plywood tank. I'm also waiting for a quote on a 1.5 inch thick piece of acrylic.

Plywood tanks are renforced with fibreglass and epoxy and have the glass placed in the front and syliconed to the fibreglass frame. The Fibreglass is covered in a thick layer of epoxy though. Check out this guys Plywood tank, it's 122inchesL x 82inchesW x 64inchesH and holds 1700gallons. Plus he only had a 3.5 inch frame on the front of the tank to hold the acrylic (I would feel safer going with a thicker frame than that myself):-
http://www.cichlid-forum.com/articles/d ... tank_1.php

I'll see what they suggest, like I said hopefully they'll have a solution
Image Image
User avatar
flash.dan
Green Spotted Puffer
Posts: 433
Joined: Fri Aug 22, 2008 9:50 am
My Puffers: 8 years of FW puffer care!
currently have 1x mbu
Bubba 17" gentle giant... loves a belly tickle.
2x Suvatti Pair
1x Carinotetraodon borneensis
Location: Coventry, UK

Re: I may've found a very cheap way to get a 1200UKgallon tank!

Post by flash.dan »

yes 2 foot high would be cheaper. the thickness of acrylic depends on how tall it is
User avatar
puffertt77
Suspended
Posts: 822
Joined: Thu Feb 05, 2009 8:19 pm
My Puffers: Mbu Puffer named Naboo
South American Puffer named Bollo RIP :(
3 Dwarf Puffers yet to be named
Red Eye Red Tailed Puffer - Returned to LFS for being to vicious
Porky the Porcupine
Pup the Dogface
Location: London

Re: I may've found a very cheap way to get a 1200UKgallon tank!

Post by puffertt77 »

I've found a place that will supply me a 10ft w x 4ft d x 4ft h fibreglass moulded tank with a 9ft w x 3 ft h hole in the front and lips behind the frame so that I can slide the glass/acrylic down into the front of the tank (I'd still need to use sylicone)

All for £800! Which is pretty good I think

I contacted one acrylic firm and they said I'd have to buy a 3metre x 2metre 30mm thick piece of acrylic for £2000!

I'm going to get glasss though as Naboo likes to bite the glass and there would be scrapes all over the place

Hopefully the glass won't be as much as £1400 but if it is that's still only £2200 versus £5000 that I was quoted for an all glass tank that was smaller than this one
Image Image
User avatar
puffertt77
Suspended
Posts: 822
Joined: Thu Feb 05, 2009 8:19 pm
My Puffers: Mbu Puffer named Naboo
South American Puffer named Bollo RIP :(
3 Dwarf Puffers yet to be named
Red Eye Red Tailed Puffer - Returned to LFS for being to vicious
Porky the Porcupine
Pup the Dogface
Location: London

Re: I may've found a very cheap way to get a 1200UKgallon tank!

Post by puffertt77 »

I've just got 2 prices for glass from the same firm

10ft w x 4ft h 25mm glass = £960

10ft w x 4ft h 19mm re-enforced glass = £788

£1760 sounds good to me for a 10ft w x 4ft d x 4ft h tank :)
Image Image
User avatar
puffertt77
Suspended
Posts: 822
Joined: Thu Feb 05, 2009 8:19 pm
My Puffers: Mbu Puffer named Naboo
South American Puffer named Bollo RIP :(
3 Dwarf Puffers yet to be named
Red Eye Red Tailed Puffer - Returned to LFS for being to vicious
Porky the Porcupine
Pup the Dogface
Location: London

Re: I may've found a very cheap way to get a 1200UKgallon tank!

Post by puffertt77 »

Hmmmm just had a thought, although I don't know where this tank will be going yet it'll have to be some where that has a 4.1 ft hole in it so that I can get the tank in :durr:

I could always take the windows out I suppose :)
Image Image
User avatar
puffertt77
Suspended
Posts: 822
Joined: Thu Feb 05, 2009 8:19 pm
My Puffers: Mbu Puffer named Naboo
South American Puffer named Bollo RIP :(
3 Dwarf Puffers yet to be named
Red Eye Red Tailed Puffer - Returned to LFS for being to vicious
Porky the Porcupine
Pup the Dogface
Location: London

Re: I may've found a very cheap way to get a 1200UKgallon tank!

Post by puffertt77 »

rough guide to tank
tank-small-use.jpg
You do not have the required permissions to view the files attached to this post.
Image Image
User avatar
Jase
Mbu Puffer
Posts: 1579
Joined: Sat Jan 12, 2008 3:13 am
Gender: Male
My Puffers: RIP Hootey :(
Location (country): USA
Location: Montana

Re: I may've found a very cheap way to get a 1200UKgallon tank!

Post by Jase »

So you're going to do this, or a company is going to do it?
-Jase
edmlfc1 wrote:A house without a puffer is not a home. :D
User avatar
flash.dan
Green Spotted Puffer
Posts: 433
Joined: Fri Aug 22, 2008 9:50 am
My Puffers: 8 years of FW puffer care!
currently have 1x mbu
Bubba 17" gentle giant... loves a belly tickle.
2x Suvatti Pair
1x Carinotetraodon borneensis
Location: Coventry, UK

Re: I may've found a very cheap way to get a 1200UKgallon tank!

Post by flash.dan »

and the filtration will still cost you a fortune. If your going for a large perm tank concrete all the way
User avatar
puffertt77
Suspended
Posts: 822
Joined: Thu Feb 05, 2009 8:19 pm
My Puffers: Mbu Puffer named Naboo
South American Puffer named Bollo RIP :(
3 Dwarf Puffers yet to be named
Red Eye Red Tailed Puffer - Returned to LFS for being to vicious
Porky the Porcupine
Pup the Dogface
Location: London

Re: I may've found a very cheap way to get a 1200UKgallon tank!

Post by puffertt77 »

Jase wrote:So you're going to do this, or a company is going to do it?
the company supplies the tank, I have to fit the glass, saw a guy on MFK do it with a 1700g tank and he only had a 3.5inch frame round the front (see link below). This is why I've gone for double that at 6 inches all round
http://www.cichlid-forum.com/articles/d ... tank_1.php
flash.dan wrote:and the filtration will still cost you a fortune. If your going for a large perm tank concrete all the way
The fact is I've got to have a huge tank for Naboo when he's fully grown. I'll build a sump for it not sure how big yet, I'll probably go by what the guy from MFK did.
I'd like to go concrete but that would also cost a fortune when treating the concrete to make it water proof and the amount of epoxy I'd have to layer it with. Plus doing a concrete tank would be like building an extention. I'd have to dig trenches and fill them with concrete as foundations and so on. I don't know maybe when it comes to it I'll look more into a concrete tank. It's just with the fibreglass tank the only thing I've got to do is fit the glass (Which I know wont be easy as It'll weigh a ton) plus these fibreglass tanks are normally used to hold waste and chemicals so they've got to be safe/long lasting.

Thanks for the words of warning though :)
Last edited by puffertt77 on Tue Mar 03, 2009 5:59 pm, edited 2 times in total.
Image Image
Post Reply