Page 1 of 2

Water change / filter question

Posted: Fri May 21, 2010 8:45 am
by asianpuffer
I was just curious what I am supposed to do with the eheim cannister filter when I am only only a water change. After changing the water, do I just plug the unit back in? i noticed that when i did this, a whole bunch of bubbles were coming out due to air. do I need do something to prevent this? empty the cannister of its water?

Re: Water change / filter question

Posted: Fri May 21, 2010 9:24 am
by Hilly
Never empty mine unless I am cleaning it out. I unplug it and plug it back in after the change and it starts up again. Sometimes I have left it on whilst draining down and refilling with a python. Edit: my spraybar points directly down though, probably not a great idea to do that if its pointing any other way.

Re: Water change / filter question

Posted: Fri May 21, 2010 11:10 am
by soggydrysuit
Hi there,

Do you have any taps or valves between the filter and the tank? Most externals do. If so, just turn off the filter then shut the valves and do your water change. When the tank is full again, open the valves then turn the power on.

If not, I'd try to stop the ends of the hoses with something non toxic to fish.

I have a fluval 404 external, with valves and it's a total nightmare to get the air out after cleaning the pads. I have to start with the thing on it's side and raise it to vertical incrementally. That's when the filter 'bucket' is full of water!

HTH

Re: Water change / filter question

Posted: Fri May 21, 2010 11:11 am
by asianpuffer
Hilly wrote:Never empty mine unless I am cleaning it out. I unplug it and plug it back in after the change and it starts up again. Sometimes I have left it on whilst draining down and refilling with a python. Edit: my spraybar points directly down though, probably not a great idea to do that if its pointing any other way.
DO i need to fill any of the tubes with water? the intake and outtake both have caps which you can uncap and fill with water.. is this what it is for?

Re: Water change / filter question

Posted: Fri May 21, 2010 11:44 am
by Hilly
I am unsure abot the caps but I wouldn't have thought there is a significance between the pro 3 which you have and the pro 2 which I have as your model is my direct replacement. When you first got it did you have to use these caps for priming the filter.

Re: Water change / filter question

Posted: Fri May 21, 2010 12:29 pm
by asianpuffer
soggydrysuit wrote:Hi there,

Do you have any taps or valves between the filter and the tank? Most externals do. If so, just turn off the filter then shut the valves and do your water change. When the tank is full again, open the valves then turn the power on.

If not, I'd try to stop the ends of the hoses with something non toxic to fish.

I have a fluval 404 external, with valves and it's a total nightmare to get the air out after cleaning the pads. I have to start with the thing on it's side and raise it to vertical incrementally. That's when the filter 'bucket' is full of water!

HTH
No taps or values. I do notice that when i am changing the water and the water line drops below the intake, water from the tube gets drained.

Re: Water change / filter question

Posted: Fri May 21, 2010 12:30 pm
by asianpuffer
No. the 3 came with the upgraded install kits for the intake and outtakes (no green intake or spraybar).
Hilly wrote:I am unsure abot the caps but I wouldn't have thought there is a significance between the pro 3 which you have and the pro 2 which I have as your model is my direct replacement. When you first got it did you have to use these caps for priming the filter.

Re: Water change / filter question

Posted: Fri May 21, 2010 12:35 pm
by Iliveinazoo
I'm not familiar with the Eheim but if it fills back up with water (primes itself) within a couple of seconds of turning it on then I wouldn't worry about it, if it stays really loud then air is trapped in it and you will have to re-prime it before turning it back on.

Re: Water change / filter question

Posted: Fri May 21, 2010 12:45 pm
by asianpuffer
Iliveinazoo wrote:I'm not familiar with the Eheim but if it fills back up with water (primes itself) within a couple of seconds of turning it on then I wouldn't worry about it, if it stays really loud then air is trapped in it and you will have to re-prime it before turning it back on.
Well once i change the water, the water goes below the water line causing the water from the intake tube to come out. When I plug the unit back in, its not loud but lots of air bubbles do come out.

Re: Water change / filter question

Posted: Fri May 21, 2010 5:27 pm
by Iliveinazoo
So if the bubbles keep on coming out for longer than a few seconds then you should prime it before switching it back on

Re: Water change / filter question

Posted: Fri May 21, 2010 5:53 pm
by jdak
Give the canister a light shake. That will knock the rest of the bubbles out.

Re: Water change / filter question

Posted: Fri May 21, 2010 7:54 pm
by asianpuffer
how would you reprime the eheim afterwards? do you empty all the water out of the cannister?

Re: Water change / filter question

Posted: Fri May 21, 2010 11:14 pm
by Brandon8521
asianpuffer wrote:
Hilly wrote:Never empty mine unless I am cleaning it out. I unplug it and plug it back in after the change and it starts up again. Sometimes I have left it on whilst draining down and refilling with a python. Edit: my spraybar points directly down though, probably not a great idea to do that if its pointing any other way.
DO i need to fill any of the tubes with water? the intake and outtake both have caps which you can uncap and fill with water.. is this what it is for?
Are these caps on the ends that are in the tank? If so then turn it off and cap them b4 you take any water out and uncap them and turn it on after your done. then it shouldnt have a way to drain any water and stay a closed system dureing the whole process. (thats if im understanding you correctly)

Re: Water change / filter question

Posted: Fri May 21, 2010 11:17 pm
by asianpuffer
Bcummings8521 wrote:
asianpuffer wrote:
Hilly wrote:Never empty mine unless I am cleaning it out. I unplug it and plug it back in after the change and it starts up again. Sometimes I have left it on whilst draining down and refilling with a python. Edit: my spraybar points directly down though, probably not a great idea to do that if its pointing any other way.
DO i need to fill any of the tubes with water? the intake and outtake both have caps which you can uncap and fill with water.. is this what it is for?
Are these caps on the ends that are in the tank? If so then turn it off and cap them b4 you take any water out and uncap them and turn it on after your done. then it shouldnt have a way to drain any water and stay a closed system dureing the whole process. (thats if im understanding you correctly)
The caps are on top of the tank on both the intakes and outtakes

Re: Water change / filter question

Posted: Sat May 22, 2010 12:42 am
by Pufferpunk
I find as long as the water level doesn't go below the intake tube while the filter is on, I don't need to prime it before turning it on. otherwise, just turn off the filter during the WC & turn it back on after the tank is full. I have all my filters plugged into a strip, so I can just flip a switch to turn them off & on. To prime the Eheim, you must fill to the top with water.