Page 1 of 2
Filstar XP3
Posted: Fri Apr 23, 2010 2:40 pm
by asianpuffer
Hi.
My aquaclear 70 is starting to make a lot of noise even after cleaning so I am trying to replace it with the filstar xp3.
I have a 38 gallon tank with 3 SAP's.
Will this filter be enough to keep the water clear and healthy? Or should I run both and put up with the noise...
AC 70<XP3??
Should I add in the ceramic rings from the AC into the XP3?
Re: Filstar XP3
Posted: Fri Apr 23, 2010 3:27 pm
by Flutter
Yes you should add the media into the XP3. I've got one of them and so far it's been perfect. It's silent and should give you more than enough filtration.
Re: Filstar XP3
Posted: Sat Apr 24, 2010 9:02 pm
by Myaj
It will do you really well.
I had the XP2 on a 33xl tank (4 foot long). It provided a pretty dang strong current, the SAP's loved it. I'm not familiar with the dimentions of a 38 gallon tank, so maybe it will work just fine. I had mine set up on the power jet shooting down the length of the entire tank.
But yes, move the existing media into the new filter

You'll love the XP series, very quiet, very easy to use.
Re: Filstar XP3
Posted: Sun Apr 25, 2010 3:39 am
by asianpuffer
Thank you for your input. The filter is all setup now...
Im just wondering if I should use the spraybar or power jet...
If i got with the spray bar, how much below the top of the water to i position it? above the water or just below it....
if I use the power jet, would it be best to have it on the opposite end of the intake tube?
Thanks
Re: Filstar XP3
Posted: Sun Apr 25, 2010 9:56 am
by Myaj
IMO, SAP's prefer a more river like current, so I'd do the powerjet at one end, intake at the other, especially if the tank is long.
If its not a long tank, more of a tall one, I might lean towards the spraybar just to cover more area.
Re: Filstar XP3
Posted: Sun Apr 25, 2010 9:59 am
by Hilly
I like to position the spraybar on externals a couple of 1-2 CM above the water at the opposite end of the tank to the intake pipe for the filer, it creates some nice aeration and not a lot of surface agitation.
Re: Filstar XP3
Posted: Sun Apr 25, 2010 12:18 pm
by asianpuffer
Myaj wrote:IMO, SAP's prefer a more river like current, so I'd do the powerjet at one end, intake at the other, especially if the tank is long.
If its not a long tank, more of a tall one, I might lean towards the spraybar just to cover more area.
The tank is 3 ft long by 20inches tall
Re: Filstar XP3
Posted: Sun Apr 25, 2010 12:19 pm
by asianpuffer
Hilly wrote:I like to position the spraybar on externals a couple of 1-2 CM above the water at the opposite end of the tank to the intake pipe for the filer, it creates some nice aeration and not a lot of surface agitation.
With this setup, do you point the holes straight out or downwards at an angle?
DO you have the bar at the very top of the tank and fill the water just 1-2 cm below that bar?
Re: Filstar XP3
Posted: Sun Apr 25, 2010 2:22 pm
by asianpuffer
Would I be able to use filter floss in place of the micro sponge at the very top of the filter?
Re: Filstar XP3
Posted: Sun Apr 25, 2010 2:35 pm
by Myaj
You could, but be aware that too much floss will quickly plug up and can block water flow. I just always used their white "floss" pad and rinsed it out ocassionally.
For a 3 foot tank I'd probably go the spraybar route or you'll be blasting your fish across the tank with the power jet. I would aim it down at an angle. I think Hilly is referring to putting the spraybar on one end of the tank facing across the length of the tank, if you didn't catch that. As far as to above or below the water line, that's up to you.. above will bring more oxygen into the water but you'll also have more noise, below will be a lot quieter.
And of course, you can play with it once its up and running and find your preference. I just would expect, considering how forceful the output of the XP2 was on powerjet in my 4ft tank, that the powerjet will be too much for a 3ft tank with the XP3.
If it happens to be too much, don't forget you can always go to the hardware store and customize your own spraybar with holes aiming different directions, longer or shorter, etc.. all you need is some PVC pipe and a drill

Re: Filstar XP3
Posted: Sun Apr 25, 2010 2:45 pm
by asianpuffer
Myaj wrote:You could, but be aware that too much floss will quickly plug up and can block water flow. I just always used their white "floss" pad and rinsed it out ocassionally.
For a 3 foot tank I'd probably go the spraybar route or you'll be blasting your fish across the tank with the power jet. I would aim it down at an angle. I think Hilly is referring to putting the spraybar on one end of the tank facing across the length of the tank, if you didn't catch that. As far as to above or below the water line, that's up to you.. above will bring more oxygen into the water but you'll also have more noise, below will be a lot quieter.
And of course, you can play with it once its up and running and find your preference. I just would expect, considering how forceful the output of the XP2 was on powerjet in my 4ft tank, that the powerjet will be too much for a 3ft tank with the XP3.
If it happens to be too much, don't forget you can always go to the hardware store and customize your own spraybar with holes aiming different directions, longer or shorter, etc.. all you need is some PVC pipe and a drill

Thanks for all the info!!! I'll probably go the spray bar route and have it about 1cm above the water line. As far as cleaning the canister since this is my first one, would you suggest cleaning them weekly? bi weekly? monthly?
As for the filter floss, i bought a ton of it when I was using my ac70...should i stick to their pads or use the floss and change them weekly?
Re: Filstar XP3
Posted: Sun Apr 25, 2010 3:36 pm
by Myaj
I would just use the pad that came with the filter, and rinse it out. No need to buy more. Filter floss is a great thing, but its really easy to use too much, or have it bunch up when you are looking at a big, wide media tray like these have.
Maintence will really depend on your tank. I really only opened mine up and rinsed everything when I noticed the flow slowing down.. and how fast that happens will depend on how much "stuff" is getting sucked into the filter. If you have a planted tank, it will probably clog up faster, as little bits of algae and plant get sucked in (especially duckweed.. I have come to have a love/hate relationship with duckweed). The high current you will have will mean more "stuff" will stay in suspention and get sucked in, especially at first.. but I wouldn't expect you'll have to tear it open and rinse more than monthy.. I often went several months

Re: Filstar XP3
Posted: Sun Apr 25, 2010 3:49 pm
by Hilly
Cheers Myaj for expanding on the stuff I didnt mention.
I like the spraybar on the side wall of the tank but my tank is wide enough so it only interrupts water on the edge of the tank. Ive never had a Rena is the spraybar longer than the width of the tank, if so and you dont fancy cutting it ust put it length ways. Doesnt really make any difference its more of a personal preference.
Re: Filstar XP3
Posted: Sun Apr 25, 2010 4:27 pm
by asianpuffer
Myaj wrote:I would just use the pad that came with the filter, and rinse it out. No need to buy more. Filter floss is a great thing, but its really easy to use too much, or have it bunch up when you are looking at a big, wide media tray like these have.
Maintence will really depend on your tank. I really only opened mine up and rinsed everything when I noticed the flow slowing down.. and how fast that happens will depend on how much "stuff" is getting sucked into the filter. If you have a planted tank, it will probably clog up faster, as little bits of algae and plant get sucked in (especially duckweed.. I have come to have a love/hate relationship with duckweed). The high current you will have will mean more "stuff" will stay in suspention and get sucked in, especially at first.. but I wouldn't expect you'll have to tear it open and rinse more than monthy.. I often went several months

The guide says to replace the top micro pad monthly...so instead, just rinse and resuse?
My tank is not planted with real plants and houses only 3 SAP's. Would it be safe to say to clean the filter once a month unless i notice a dramatic decrease in flow?
Re: Filstar XP3
Posted: Sun Apr 25, 2010 4:29 pm
by Hilly
Yes just rinse it out, if it starts to fall apart then replace it.
Yes once a month should be fine, I doubt with that bioload in the tank and what the XP3 is rated for you will see any decrease in flow.