Page 1 of 1

Emergency Filter build take 2

Posted: Wed Dec 30, 2009 11:49 pm
by Dadof4
Ok, sorry bout that. For those of you who were watching the thread earlier, I deleted it because I was having camera issues and I didn't want the thread to slip away. I lost all the picture of the build itself but I have pics of the filter up and running and go through all the particulars of how it works. Everything that is done here was found on this site in one shape or form, I just put it together and cataloged it. I'm going to keep the thread locked as I go and open it for discussion after the build is complete just to keep the continuity of the build intact.

So, we were some where about here......*flash back to a few days ago*......

Some essential pieces of equipment for any DIY build:
Image
Image

The rest of the list of parts is to follow later tonight.
To start, you need roughly 15 feet of PVC pipe, diameter is dependent on how much flow you are looking for. For this one I went with a 3/4 inch Schedule 40 PVC pipe and the parts list is based off that. You can up-size everything as needed.

Re: Emergency Filter build take 2

Posted: Fri Jan 01, 2010 3:32 pm
by Dadof4
Alright, so my "later tonight" took a little longer than expected, happens when you have your own herd of kids and a job that can call you in at a whim....

So, we left off with the parts list and the knowledge that 3/4 inch schedule 40 PVC pipe was used.

The rest of the list:

7 90 degree elbows with slip fittings
Image

1 3/4 slip fit to male thread adapter
Image

2 3/4 slip fit ball valves
Image

2 slip fit "T" joints
Image

1 3/4" male threaded to 1" slip fit reducer
Image

1 female threaded cap
Image

1 90 degree female threaded to slip fit 90 degree elbow
Image

1 5 gallon bucket with lid. I like the Red Sea Marine Salt buckets because the lid is divided nicely.
Image

Drinking water quality PVC glue.
Image

Some egg crating I got by with a 4' x 2' sheet
1 large Rubbermaid container, a long low 20 gallon worked nicely.
1 return pump
Vinyl tubing for a return line.

For tools:
Hammer, hacksaw, sandpaper, drill with multiple size drill bits, channel lock pliers, a power sander and
1 PVC pip cutter
Image

OK, I'm getting long winded and I have a few things to do for the wife before she whacks me. I'll continue on when chores are done.....

Re: Emergency Filter build take 2

Posted: Tue Jan 05, 2010 10:28 pm
by Dadof4
So, chores are done, wife is happy, she has given me permission to continue.

First thing you need to do is clean the pipe because it was probably sitting in a filthy warehouse. I clean the outside of the pipe by wiping it down with rubbing alcohol and then letting it dry. Rubbing alcohol dries without leaving a residue and is aquarium safe. After every cut I clean the inside of the pipe with a cotton ball or a cloth soaked in alcohol that I push through with a piece of wire. Oh, do not glue any of this together until the very end.

The first cut you will need to make is to a length approximately 2/3 the way down your tank from the top rim. At the top of this piece you will want to add a 90 degree slip elbow and at the bottom of the piece you will want to add a slip fit Ball Valve for emergency shut off/flow control. After the Ball valve you need to cut and add another piece of pipe with a slip fit "T" joint at the bottom. What you want to end up with a run of pipe that goes 90 degree elbow facing over the rim of the tank, pipe, ball valve, pipe, and then "T" joint, with the "T" joint pointing under the tank and the top of the "T" about 2 feet off the floor.

To the "T" joint you need to add a 3 inch piece of pipe and a slip fit 90 degree. With the "T" pointing away from you the 90 degree elbow should point to either the left or the right (I drew it to the right) parallel to the tank. Add to that 90 degree elbow another piece of pipe about 3" long, another 90 degree elbow that points towards the top of the tank and, a piece of pipe that runs to about even with the top of the tank. To this piece of pipe add a 3/4 slip fit to male thread adapter and it's associated female threaded cap. For the cap, drill a 1/8 inch hole in the center of the face to allow for some airflow in to the system. If done correctly you've just made a huge "U", if you haven't, go take some aspirin, say a few choice words, and try again!

Kind of like this (don't laugh at my mad skills with KolourPaint):
I've color coded the pieces in the drawings as such:
Yellow=PVC pipe
Grey= 90 degree slip elbow
Red= Ball Vlave
Green= "T" joint
Funky Purple= 3/4 ince male threaded adapter and female threaded cap

Image

To the open end of the "T" add a piece of pipe about 3 inches long and add another ball valve (for help in starting the system). To that add another piece of PVC that is long enough to reach the center of the tank from front to back. It should look like this:
Image

At this point we need to take it over the top of the tank. To the 90 degree slip elbow on the top, add a piece of pipe roughly 1 1/2 inches long and then another 90 degree slip elbow so that the end points down, like the picture above shows.

This will start to make more sense as it goes together further. The inside pieces have major impact on the water level in your tank and some impact on the flow rate and I feel that this area of construction needs a night of discussion to itself, so I leave you here until my next night off!

Re: Emergency Filter build take 2

Posted: Mon Jan 11, 2010 7:13 am
by Dadof4
Alright, back to it. So far we've got the main part of the plumbing built, now we need to take a look at the plumbing on the inside of the tank. This area acts like an overflow would on a marine tank and is not only responsible for the water leaving the tank but also for the water level maintained in the tank.

So, for this post I am going to talk about the pipes as if I were looking from the front of the tank.

From the last 90 degree slip elbow add a piece of PVC pipe about 5-7 inches long (it really doesn't matter) and at the bottom of that piece add a 90 degree slip elbow so that the open end points off to the right. To that add a piece of PVC about 2 inch long and then another 90 degree slip elbow so that it ends with the open end pointing up. This next piece of PVC is the critical one. This needs to be cut to the level you want you water to be when the filter is running. The water in your tank will drain to approximately the level of this pipe, give or take about 1/4 inch. This piece gets added to the 90 degree elbow that is pointing up. You could leave off here with out adding the rest of the in tank plumbing but you will get a gurgling and sucking sound as water moves down this pipe. To counter this I used a modification of a Durso stand pipe. On the top of the last pipe I places a slip fit "T" joint so that the "T" points to the right. On the open end that is pointing up I put a female slip fit cap. Some find it necessary to add a small airline flow control valve here so they can occasionally vent the system or add a little air so the system doesn't air lock. On the "T" piece add a piece of PVC about 2 inches long and then a 90 degree slip fit elbow. To this last elbow I added a 2 inch piece of PVC pipe and a strainer from an old filter.

When all this is assembled it should look like this:
Image

So, now most of the plumbing is done! The next step is testing the flow. Push all the pieces together as described and as you can see the pieces fit together pretty tightly and do not need to be glued yet. Hang the plumbing over the tank and turn off the ball valve on the bottom piece that is under the tank. The end coming up the back of the tank that is capped is you starting mechanism. Uncap the pipe and suck on it, not much more to it than that! You want start a siphon through the other pipe that will eventually flow out the pipe that goes under the tank when you open the ball valve. This part can get tricky as the pipes can trap air and getting the trapped air out to get a good uninhibited flow is a challenge. I'm still working on different methods to help with this but the best I have found so far is to try to suck as much water up the vent pipe as possible and then letting it flow back. I do that a few times and all the air is gone. Once you've done that get something to catch water and place it under the pipe that is under the tank and open the ball valve. The flow may be a little slow at first but should pick up quickly. With 3/4 inch PVC you should get around 600-800 gph flow. If it seems very slow you have air in the pipes and need to try to get it out again.

Once it is flowing well it really pours so be prepared (I wasn't) so you don't quickly over fill your catch bucket. I have a few ideas I'm toying with to take care of the air trapping issue and I'll touch base on that again once I find an easy solution.

So, next step is the cool part, making the filter itself!