Page 1 of 2
Hang On the Back Filter - one last Q!
Posted: Sat Jun 13, 2009 1:30 pm
by lilacamy931
Got a new tank and for this one there is a hang on the back filter (Aqua One Clear). I wish to cycle in my main established tank for two weeks to get some of the good stuff in it. Have added the media, but how I have placed is it ok like so in the tank?
Here are some piccys:
As the hood is an extreme tight fit, this was the only way could think of having it in the tank? Do you think this will be ok for the puffs, may drape a flannel or something to cover the gaps to avoid temptation of jumping.
Also how do I start it up as it did not come with instructions? Do I need to fill up with water first then turn on?
Sorry for all my questions recently!
Re: Hang On the Back Filter
Posted: Sat Jun 13, 2009 1:40 pm
by edmlfc1
Yes fill it with "tank" water then turn it on, it should start working.
For the gap you could use a piece of egg crate, which is lighting cover to close the gaps. Or you can do what I did in a hurry once. I used the glad cling wrap and taped the edges down. It worked so good I left it there for a month.

Re: Hang On the Back Filter
Posted: Sat Jun 13, 2009 1:45 pm
by lilacamy931
Do you mean the stuff you can wrap sandwiches in etc (or am I confused!!!) LOL you know me edmlfc1!
Right think I will install tomorrow after a water change (think it is about time after all my great 0 readings) and leave for a good two weeks.
Thanks again edmlfc1 (really hope filter works!)
Re: Hang On the Back Filter
Posted: Sat Jun 13, 2009 1:49 pm
by edmlfc1
Yeap that's the stuff. Sandwich wrap! It's good for keeping the salt creep off the walls.

Re: Hang On the Back Filter
Posted: Sat Jun 13, 2009 1:51 pm
by lilacamy931
LOL will definately give that a go, loads better than balancing the lid

THANK YOUUUUUUU!!!! tee hee (sorry had sugar

)
Re: Hang On the Back Filter
Posted: Sat Jun 13, 2009 2:02 pm
by edmlfc1
Forgot to mention: If you use the cling wrap don't put it too close where the water goes back into the tank. You might end up draining half your tank onto your floor.

You can bring it over and tape it off on the top of the filter if you have too, or on the sides so that you can still remove the filter's lid for cleaning.

Re: Hang On the Back Filter
Posted: Sat Jun 13, 2009 2:18 pm
by lilacamy931
Don't worry did think of that and didnt want to contaminate the tank with anything that may be on the plastic! (though saying that...hmmm.. yeah there may have been puddles

) It does seem you know me too well
I also have a pump and pieces which I hope to use at one point and no idea how to connect up but I will leave that till another time

Re: Hang On the Back Filter
Posted: Sat Jun 13, 2009 2:52 pm
by Iliveinazoo
that seems to be a very small gap so you'd probably get away with leaving that section off, personally I would leave it off and take the risk.
i've just recently taken one of them style filters off my puffer tank because it was leaking and i couldn't get it to stop. the one on my fiddler tank is working a treat though
Re: Hang On the Back Filter
Posted: Sat Jun 13, 2009 3:36 pm
by julianchan
if you are handy with tools, you could do a little cutaway with a saw, or mark out where you need to cut and ask someone to do it, then file the rough parts out and seal it with some aquarium safe glue, just so you dont cut yourself....
Re: Hang On the Back Filter
Posted: Sat Jun 13, 2009 7:18 pm
by LilGreenPuffer
I've used plastic wrap. It works!
Re: Hang On the Back Filter
Posted: Sun Jun 14, 2009 2:29 am
by Pufferpunk
That filter looks really small, especially that tiny sponge. How big is the tank it's going on? What fish will you be housing in there? What's the GPH, do you know? You can look the filter up on most online aquarium store sites, I would think.
Re: Hang On the Back Filter
Posted: Sun Jun 14, 2009 2:44 am
by Troender
I don't know that spesific brand of HOB filter, but I know of one thing you have to be careful with (someone I know experienced this recently, and I also know another one experience it some time ago. But both experienced it with Eheim Liberty HOB filters): Make sure the filter is absolutely in level or leaning a little bit against the tank. If it's leaning the other way, you can get a wet floor if it gets clogged. If something is clogging the water flow, you can get an overflow. And with the filter on back of the tank, it's sometimes difficult to spot. That friend of mine spotted it because there was water lacking from the tank, not because she found water on the floor. The water had followed the wall, and went behind the list, and then down to the next floor. If the filter leans a little against the tank, the overflow water will go into the tank again, and not down the back of the filter.
Re: Hang On the Back Filter
Posted: Sun Jun 14, 2009 5:01 am
by lilacamy931
Blimey! I will certainly keep an eye on that and monitor daily for overflows thanks Troender!
The filter I can place two sponges in (not installed yet just seeing if I could get it hanging, so it will have two). It will be going on a 38 litre (originally came with the tank along with all the other bits and pieces off Ebay) and I will only be stocking with Guppies in small groups of 3 (only males). And have a very gradural stocking.
Just looking on the net... actually scrap that on the base it says 300 l/h. Definately will put two of the sponges (using same as from my Fluval 2 plus in the other tank) just needs a little trimming. Hope this is ok

Re: Hang On the Back Filter
Posted: Sun Jun 14, 2009 8:43 am
by lilacamy931
Have installed on the main tank with two pads. Tad worried as the puffs seem reaaallll unsure on the extra current (they arent keen on the Fluvals current).
Would it be better for me to before placing in the tank put an established media from the main filter into this one, rather than run in the tank? Any opinions valued.
There were a couple of dribbles down the side of the tank, I will keep an eye on to make sure no bad things happening, fingers crossed will be ok.

Re: Hang On the Back Filter
Posted: Sun Jun 14, 2009 3:37 pm
by Pufferpunk
Fold up some cardboard &b place it between the bottom of the filter & the tank, so the bottom is tilted away from the tank. That will solve that problem.