Page 1 of 1

Question about Prime

Posted: Fri Apr 24, 2009 7:25 pm
by LilGreenPuffer
I got a bottle of Prime today! Phew! It was $7.11 for 1.7oz, but I needed it.

My question is about dosing. My tap water has about 1ppm of ammonia, plus chlorine and chloramines. It says that 2 drops eliminate .0 mg/L ammonia, 1.2 mg/L chloramine, or 3.3 mg/L chlorine. So, to remove all of these (assuming that this is the amount of each substance I have in my water), do I need to add 2 drops, or 6?

Re: Question about Prime

Posted: Fri Apr 24, 2009 11:33 pm
by LilGreenPuffer
Never mind!

Re: Question about Prime

Posted: Sat Apr 25, 2009 12:10 am
by Jase
Just so you know... I add a small splash. ;)

Re: Question about Prime

Posted: Sat Apr 25, 2009 2:23 am
by LilGreenPuffer
I did that with my other dechlorinator, and I of course would err on the side of too much, and so I ran out really fast. Prime is freaking expensive! Anywho, Dadof4 helped me out, so I gots it. :)

Re: Question about Prime

Posted: Sat Apr 25, 2009 6:03 am
by DRRT
buy it in BULK

still expensive, but per unit price is reduced
http://www.marinedepot.com/ps_ViewItem. ... ild=SC4739

never had a problem with prime. when i would bleach the plastic decour, i would rub some prime on my hands and was confident enough to stick my hands into the tank to continue cleaning the system. never ever had a problem

Re: Question about Prime

Posted: Sat Apr 25, 2009 10:51 am
by Jase
I did measure it for a while, but became lazy...
I used a measured water syringe I got from my dentist.

Re: Question about Prime

Posted: Sat Apr 25, 2009 5:38 pm
by LilGreenPuffer
Oh, that's a good idea. Maybe the pharmacy has them!

Re: Question about Prime

Posted: Sat Apr 25, 2009 8:31 pm
by emartin
LilGreenPuffer wrote:I got a bottle of Prime today! Phew! It was $7.11 for 1.7oz, but I needed it.

My question is about dosing. My tap water has about 1ppm of ammonia, plus chlorine and chloramines. It says that 2 drops eliminate .0 mg/L ammonia, 1.2 mg/L chloramine, or 3.3 mg/L chlorine. So, to remove all of these (assuming that this is the amount of each substance I have in my water), do I need to add 2 drops, or 6?
I'd either buy the 2liter or 4liter bottle of Seachem Prime, or buy a bucket of ChlorAm-X powder (which happens to be FDA approved for food fish also).

Both are available here: http://www.kensfish.com/waterconditioners.html

~Ed

Re: Question about Prime

Posted: Sat Apr 25, 2009 8:50 pm
by LilGreenPuffer
Thanks, guys. I only have a 10g, so four liters would probably be too old by the time I finished it, and I won't need any once ammonia levels in the tap go back to normal, so I'll be using the cheap-o dechlorinater again soon. I can't really afford the expensive stuff too often. :(

Re: Question about Prime

Posted: Sat Apr 25, 2009 10:01 pm
by emartin
LilGreenPuffer wrote:Thanks, guys. I only have a 10g, so four liters would probably be too old by the time I finished it, and I won't need any once ammonia levels in the tap go back to normal, so I'll be using the cheap-o dechlorinater again soon. I can't really afford the expensive stuff too often. :(
As long as you cap the Prime bottle it will be fine, it won't go bad at all. What I do is I buy the 2liter bottles and use it to refill my 250mL Prime bottle instead of taking the liquid directly from the large bottle each time.

Up to you though, whatever works best with you and your budget. I need to buy in bulk though since I have like 13 tanks and two of them are 120g and 265g...

Re: Question about Prime

Posted: Mon Apr 27, 2009 1:39 am
by Nick
I took an old bottle "dropper" type bottle of API tap water conditioner and refill it with either a big bottle of the API or prime, depending on needs at the time. It's just like the dropper bottles the API test kits use, so it's really easy to measure doing drops, I think prime uses about two drops per gallon, while the API tap water conditioner needs 3 drops for every two gallons. Saved me a lot of money, I found I was using almost 3 times what I really needed once I switched to the dropping measurement method!

Re: Question about Prime

Posted: Mon Apr 27, 2009 1:54 am
by Pufferpunk
I also use the large pond-size & pour it into a smaller bottle for dispensing. Hint: 1 ml dropperful, treats about 20g.