Page 2 of 2
Re: Filstar XP3
Posted: Sun Apr 25, 2010 4:42 pm
by asianpuffer
Hilly wrote:Yes just rinse it out, if it starts to fall apart then replace it.
Yes once a month should be fine, I doubt with that bioload in the tank and what the XP3 is rated for you will see any decrease in flow.
Thank you Hilly, Myaj and Flutter for all your input.
How often should I chance the stars and the ceramic rings I put in from my old filter?
Re: Filstar XP3
Posted: Sun Apr 25, 2010 9:02 pm
by Myaj
You don't really change the ceramic ones. I mean, technically, they get "plugged up" over time, and you could take some out and boil them to steam clean them (never all at once).. but these are permanent "media". I never bother with anything more than a rinse, myself.
Are the "stars" ceramic or do you mean the foam thingies? If they are foam, just rinse and reuse, no need to do more than that unless they fall apart over time.
Re: Filstar XP3
Posted: Mon Apr 26, 2010 10:25 pm
by asianpuffer
Got it.
Now that Im not using the AC70, the top of the aquarium is left with floating dust sheets...anyway to get rid of this?
Would a airstone help?
Re: Filstar XP3
Posted: Tue Apr 27, 2010 4:01 am
by Hilly
Do you mean like a scummy film of dust on top of the water An airstone might speed it up and cause the dust to sink by agitating the water surface more, it should go in time anyway on its own with water changes.
Re: Filstar XP3
Posted: Wed Apr 28, 2010 6:29 am
by Nick
Not enough agitation on the surface form the water returning to the tank from the filter.
http://www.amazon.com/KOLLER-CRAFT-Surf ... B00176MUKY
Will continually skim the waters surface to increase 02 moving into the tank from the air above. If you are creative, you can find a way to attach it to most filters.
Re: Filstar XP3
Posted: Fri Apr 30, 2010 8:33 pm
by asianpuffer
ok so i repositioned the spraybar about 1 cm above water level. Now there are tiny bubbles everywhere from the spraybar hitting the water...stupid question but is that normal?
Re: Filstar XP3
Posted: Fri Apr 30, 2010 9:26 pm
by Nick
Yes. You can reposition so it does not cause bubbling, so long as it agitates the surface water such that good oxygen exchange can take place.
Re: Filstar XP3
Posted: Fri Apr 30, 2010 9:33 pm
by J-P
that will work for a few days until you have evap and it makes bubble again
just my opinion, try to position it so that when it creates bubbles after a week, you'll know when to do your water changes

I measured my pumps with a strip of painter's tape when the tank was full and again 1 week later. I positioned almost everything at the 1 week level. Once the pumps started foaming I knew I had a water change due.

Re: Filstar XP3
Posted: Fri Apr 30, 2010 10:54 pm
by Flutter
I top up the tank every day

My spraybar is about 2" under the surface and provides a nice surface current.
Re: Filstar XP3
Posted: Sat May 01, 2010 8:17 pm
by asianpuffer
When i had the bar one inch below the water line, the top of the surface would not get any movement. How are you getting surface movement with the bar being under 2"
Re: Filstar XP3
Posted: Sat May 01, 2010 8:19 pm
by J-P
depends on the angle
Re: Filstar XP3
Posted: Sat May 01, 2010 11:30 pm
by Flutter
Weird. Ours is directly at horizontal and provides enough surface current to provide oxygen to the fish (which are currently all bottom dwellers) with the addition of CO2. We actually get so much surface current that it needs to be turned off for feeding.
Re: Filstar XP3
Posted: Sun May 09, 2010 11:39 pm
by asianpuffer
On another note...
Ever since i switched over from my AC 70 to my xp3, my nitrate levels have been really low..Before the nitrate level would be around 10-20 or so after a few days of a water change.. Now with this filter when I test the water I get 0, 0 and 0-10 for the nitrate levels...I used the ceramic balls from the ac unit along with the stars the new unit came with.
Is this normal?